新型除草剂精草铵膦对柑橘园杂草的田间防效

[目的]为评价新型除草剂精草铵膦对柑橘园杂草的田间防效。[方法]采用定向茎叶喷雾法,分别于2018、2019年进行了10%精草铵膦钠盐可溶液剂的田间小区试验。[结果]10%精草铵膦钠盐可溶液剂570~870 g a.i./hm^2对柑橘园阔叶杂草、禾本科杂草均具有较好的防效,药后30 d,总草株防效和鲜重防效分别为94.9%~98.8%、95.0%~98.5%,与对照药剂200 g/L草铵膦水剂1400 g a.i./hm^2处理相当。[结论]精草铵膦可作为防治柑橘园或非耕地杂草的高效低用量药剂,具有较好的推广应用前景。     

双盘式磁力耦合器振动噪声分析与实验研究

为了在双盘式磁力耦合器设计阶段分析振动噪声特性,优化双盘式磁力耦合器设计,提出了一种利用模态叠加原理来分析其振动噪声的方法。双盘式磁力耦合器具有高转矩密度与高效率等优势,因此逐渐发展成为煤矿机械柔性传动装置。由于双盘式磁力耦合内部的转子磁场非正弦分布以及涡电流谐波等因素影响,双盘式磁力耦合器输出转矩中不可避免的存在波动。若根据计算得出的双盘式磁力耦合器的电磁振动噪声特点,在设计时选取振动噪声小的参数进行优化组合,可在实际中降低其电磁振动及噪声,有利于减少制造成本。本文结合双盘式磁力耦合器的结构特征,提出了一种模态叠加响应法计算电磁振动噪声,建立了其电磁径向力的解析模型,并在多物理场耦合作用下分析主要电磁径向力波在工作频率内的谐波响应,最后在额定功率为55 kW双盘式磁力耦合器实验台上进行试验验证。基于麦克斯韦张量法,建立了双盘式磁力耦合器的径向电磁力解析模型,并得出0阶与10阶电磁径向力波是产生振动噪声的最主要原因;利用多物理场耦合分析法进行谐波响应NVH特性分析,结果显示0阶力波的振动加速度与形变量均大于10阶力波的振动加速度与形变量,因此双盘式磁力耦合器的电磁振动主要来源于0阶力波;在额定功率为55 kW,最高转速为1 500 r/min的双盘式磁力耦合器实验台进行振动测试,试验结果显示在1 500 r/min时,试验得出的最大振动峰值及频率约为35 m/s^2和4 950 Hz,与有限元仿真结果的误差对应为6.3%和1.1%;而当变频电机的输入转速依次增大时,振动加速度的理论值、仿真值与试验值的曲线形态较为接近,误差较小;噪声估计值与实测值的最大误差仅为8.9%,基本验证了本文所提出模态叠加法的正确性。     

淬火硝盐的劣化和再生

使用扫描电镜及能谱分析、化学分析方法,全面分析了使用硝盐浴进行分级淬火和等温淬火时,淬火硝盐劣化产物。结果表明:硝盐反应生成物(Na₂CO₃、NaOH),设备(主要是盐槽、盐泵、管道)、夹具、料盘及工件等氧化产物(FeO·Fe₂O₃·Fe₃O₄),外来物(灰尘,炭黑)是造成硝盐劣化的主要原因。据此,提出了预防淬火硝盐劣化措施:选用品质好的基盐;选用热稳定性较高的混合盐;保持淬火盐浴温度均匀,淬火前后温升可控,尽量避免“瞬间”过热使用;尽量避免外来杂质进入;做好日常维护。并简要介绍了淬火硝盐再生处理方法。     

矿用无人卡车国内外研究现状及关键技术

分析了国内外露天矿山用卡车无人驾驶技术发展现状,详细介绍了露天矿山卡车无人驾驶关键技术;通过分析对比前装线控和后装线控两种技术路线的优缺点以及超声波雷达、毫米波雷达、激光雷达、4D光场智能感知系统、红外传感器、视觉传感器等环境感知技术的优缺点;提出多传感器高度融合将是露天矿山卡车实现全天候环境感知的发展方向。通过分析对比惯性导航系统、GNSS差分定位技术、车联网定位技术、电子地图定位技术、视觉传感器等定位导航技术的差异,指出多定位技术融合是露天矿山无人驾驶卡车定位方式的必然选择。结合露天煤矿的生产实际,提出将现有的无人驾驶各种技术算法与露天矿山标准作业流程有机融合是实现卡车无人驾驶的必由之路。最后指出无人驾驶卡车应用5G技术是露天矿山安全生产的关键和核心,是无人驾驶的必备技术。     

Effects of sintering in a high magnetic field on properties of vitrified bond and vitrified CBN composites

Vitrified bond CBN grinding wheels are being widely used due to their superior performance. Also, advantages of vitrified grinding wheels are high elastic modulus, stable chemical property, and low thermal expansion coefficient. Brittleness and low strength are key factors restricting the development of vitrified bond CBN grinding wheels. In this paper, the sintering in a high magnetic field was innovatively introduced into the manufacturing of vitrified bond CBN grinding wheels, and the effects of sintering in a high magnetic field on properties on vitrified bond and vitrified CBN composites were systematically investigated. Vitrified bond was characterized using three-point bending, scanning electron microscopy, X-ray diffraction. It was observed that microstructure of vitrified bond could be changed, grain orientation could be controlled and average grain size could be decreased in a high magnetic field, while vitrified bond strength could be simultaneously improved. High quality vitrified bond could be obtained by appropriately adjusting the strength and direction of high magnetic field. Results demonstrated that vitrified bond properties were improved when the magnetic field strength was 6?T. In order to highlight the high magnetic field effect on the vitrified CBN composites, the ordinary CBN abrasives and nickel plated CBN abrasives were used respectively. Microstructures, bending strengths of vitrified CBN composites were compared in different high magnetic fields. When the magnetic field strength was appropriate (less than 6?T), the binding characteristic of vitrified bond CBN composites with nickel plated CBN abrasives was greatly improved. The highest bending strength value of vitrified CBN composites was 79.5?MPa in 6?T high magnetic field.     

Leakage mechanisms of partially self-polarized BiFeO3 film

Partially self-polarized BiFeO₃ (BFO) film was fabricated on Pt(111)/Ti/SiO₂/Si substrate by a metal organic decomposition process at 480?°C. The influence of soaking times on leakage properties was discussed. The soaking times considered were those that could keep the leakage currents being measured in a steady state condition during the leakage tests. The length of soaking time during leakage measurement should be greater than or equal to 500?ms to rule out the contribution of backswitching to leakage properties. Different leakage characteristics induced by the built-in negative field occurred under positive and negative fields. The "flat-band" feature of the leakage current curves may result from competition between domain switching and the switching of defect complexes. It is suggested that the "unswitched" mode should be adopted during leakage measurement in BFO films. Additionally, negative bias should be adopted in negatively polarized BFO films and positive bias should be adopted in positively polarized BFO films.     

Flash Sintering using Controlled Current Ramp

In conventional flash sintering, the current rises nonlinearly to a set current limit, accompanied by a spike in the power density. This sudden power spike may cause hot spot formation, in which current preferentially channels through a small area, causing localized melting while other areas remain unsintered. By using a controlled current ramp early on the sudden power spike can be avoided. In addition, by changing the ramp rate material properties such as porosity, grain size and conductivity can be tuned.     

Significantly enhanced breakdown field in Ca1-xSrxCu3Ti4O12 ceramics by tailoring donor densities

Significantly enhanced breakdown field of 24.52 kV cm^?1 as well as noteworthy nonlinear coefficient of 8.11 and low dielectric loss of 0.077 were obtained in Ca_0.6Sr_0.4Cu₃Ti₄O₁₂ ceramic. It was proved from impedance spectra that improved breakdown field was attributed to enhanced grain boundary resistance and elevated Schottky barrier height, which was further found resulting from reduced donor densities in C-V measurements. In addition, it was found that the activation energy originated from oxygen vacancies was increased, indicating the generation of oxygen vacancies was suppressed. Since oxygen vacancies acted as donors in depletion layers, it is reasonable to deduce that the reduced donor density was mainly ascribed to the decreased oxygen vacancies. In conclusion, maximum integrated action of strong solid solution effect and weak Sr-stretching effect was achieved when Sr/Ca ratio is 40/60, leading to greatly elevated potential barrier height and enhanced breakdown field consequently.